How to make Remote Control Home Appliances using Arduino Nano/Uno.

How to make Remote Control Home Appliances using Arduino Nano/Uno.

Hello, Friends Welcome to my channel ElectriCircuit Today Video is How to make Remote Control Home using Arduino Nano/Uno. using my prevision video relay module and IR remote decode.

How to Decode IR Remote Value Using Arduino UNO:- https://youtu.be/TXoin8xyX6Y How To Make a 5V Relay Module At Home and Check using Arduino:-

https://youtu.be/ZMewjmbJu4c

Required Components:- -Arduino NANO -Breadboard -TSOP 1738 (IR receiver) -Jumper wire - Relay Module -Bulb -Bulb holder

Code, Circuit Diagram Download Link:-

https://drive.google.com/drive/folders/1pP3uRvI-7w2URqKZAhKwqGkoAgcwvVE1?usp=sharing

Comments

How To Control 12v RGB Led Strip Using Arduino And BC 547 Transistor With Code

How To Control 12v RGB Led Strip Using Arduino And BC 547 Transistor With Code Hello, Friends Welcome to my channel Electrify Circuit Today Video How To Control RGB Led Strip Using Arduino And BC 547 Transistor. View full video. Required Components:- -Arduino NANO -Breadboard -RGB Led Strip -Jumper wire - BC 547 Transistor Circuit Diagram:- Video:- Code, Circuit Diagram Download Link:- Click Here Others Videos:- How to Test Esp32 Bluetooth Led On/Off To App:- https://youtu.be/AiQ5IF_j--k How To Make a 5V Relay Module At Home and Check using Arduino:- https://youtu.be/ZMewjmbJu4c How to Decode IR Remote Value Using Arduino UNO:- https://youtu.be/TXoin8xyX6Y LED shifting using push-button and Arduino nano:- https://youtu.be/9uNiHqaziqs 7-segment 0-9 counter using Arduino Nano:- https://youtu.be/hTY3PsQ7H9A How to test Arduino Nano | How to led blink with Arduino nano:- https://youtu.be/Rbdl2Ii10b0 How to make full bridge rectifier | 0 to 12v voltage regulator | Rec

HowTo Make Variable Power Supply Using LM317

How to make variable power supply using lm317 | #newvideo2021 #newvideo #voltageregulator #variablepowersupply #diy #lm317 #bd139 #tip3055 This Project is to make a simple variable Power supply in LOW cost. Mager Components LM317-: The LM317 is an adjustable 3-terminal positive voltage regulator capable of supplying different DC voltage outputs other than the fixed voltage power supply of +5 or +12 volts or as a variable output voltage from a few volts up to some maximum value all with currents of about 1.5 a mperes. BD139 Transistor:- BD139 is an NPN transistor hence the collector and emitter will be left open (Reverse biased) when the base pin is held at the ground and will be closed (Forward biased) when a signal is provided to the base pin BD139 has a gain value of 40 to 160, this value determines the amplification capacity of the transistor. The maximum amount of current that could flow through the Collector pin is 1.5A, hence we cannot connect loads that consume more

How to Test Esp32 Bluetooth Led On/Off To App

How to Test Esp32 Bluetooth Led On/Off To App #arduino #esp32 #arduinoproject # NodeMCU Hello, Friends Welcome to my channel ElectriCircuit Today Video is How to test Esp32 Bluetooth using App make an app using MIT App inventor. One led On/off Using Android App. Required Components:- -ESP 32 Board -Breadboard -LED -Resistor -Jumper wire Code, App, Circuit Diagram, aia file Download Link:- Click Here

Electrify Circuit

Search This Blog